Part VI in Java

Access EAN 13 in Java Part VI

The revolve profile sketch is not on an identifiable sketch plane that you can reuse for other features, although that would be useful. You can change the sketch dimensions outside of the wizard interface, and if you later use the wizard to edit it, then the changes appear in the Custom Sizing panel. Figure 17.3 shows the Custom Sizing panel with the changed counterbore diameter highlighted.

pulse. The measurement conditions are shown in the schematic. (After Bourcerie et al., Ref. 29, 1990 IEEE.)

broadband local loops, as the frequency ranges far exceed 4 kHz. Where such services are to be deployed, the local loops must be properly conditioned, which entails removing the load coils and other impediments. The presence of a load coil also has the effects of increasing the impedance of the circuit and reducing the velocity of propagation, that is, speed of signal propagation, to 10,000 12,000 miles per second. This speed penalty is not of particular signi cance in short voice-grade local loops. If the loops are long, however, load coils can create unacceptable problems with echo, or signal re ection. At any point in a circuit where an electromagnetic wave meets a discontinuity, a portion of the wave is re ected back in the direction of the transmitter. Such discontinuities can be caused by impedance mismatches, mismatches between line and balancing networks, irregular spacing of loading coils, and a host of other anomalies that are beyond the scope of this book. Now, echo is not a problem for human-to-human conversations as long as the echo return is not longer that 30 40 milliseconds (ms), which means that a circuit that propagates electromagnetic waves at near the speed of light (186,000 miles per second) can be 3000 4000 miles long without creating an echo problem. However, a circuit of 1000 miles with a signal traveling at 10,000 miles per second returns an echo in 100 ms, which makes conversations nearly impossible. In contemporary networks, high-speed carrier circuits are conditioned, with loading coils removed, so the problem largely disappears except in international communications or where satellite circuits are involved. Contemporary networks also are designed with echo cancelers or echo suppressors to deal with this problem, although it still occurs on occasion when echo suppressors fail. 1.6.2 Ampli ers (Analog)

The DimXpert is a tool to apply reference (driven) dimensions with tolerances to models and drawings. DimXpert employs feature and topology recognition so it can work on either native data or imported data. Use the DimXpert tab at the top of the part Feature manager, and click the Autodimension Scheme button (the first button on the left) to apply dimensions to the entire model based on selected datums. The goal of DimXpert is to comply with ANSI Y14.41, which deals with 3D annotated models. The general consensus on this is that neither the standard nor the DimXpert tools are up to the rigors of daily production use at this time. The concept seems compelling, but the implementation is not yet practical. When you use the dimensions and tolerances created with the DimXpert in conjunction with the TolAnalyst, you are able to do simple stack-up analysis. TolAnalyst is outside the scope of this book, because it is part of the Premium package and I confined this book to SolidWorks Standard. A limitation of this system is that you can only apply location or size dimensions; you cannot apply non-dimensional geometric form tolerancing such as parallelism, cylindricity, or flatness. All controls must drive size or location, and have associated dimensions. When you use the DimXpert on a drawing, it first places a datum at a vertex or centerpoint. After that, it automatically dimensions the entire feature in the view that is the parent of the edge you select. Figure 23.5 shows the Dimension PropertyManager when DimXpert is activated. The image

The wp_register_script(), wp_enqueue_script(), and wp_print_scripts() functions are described in 5. n

Father Time must be astounded at the extent to which the telephone has challenged him in a domain over which he has long held undisputed sway. The voice travels over telephone wires and cables at between 10,000 and 180,000 miles per second. By radio its speed is the same as that of light. Telephone Almanac, American Telephone & Telegraph Company, 1937

There is a specific group that exists with permissions to edit the schema, Schema Admins. By default, the local administrators group of the Schema Operations Master is added to this group. Add users to this group who will participate in the editing of the schema. See the Best Practices section for more on permissions and strategy on the schema.

- ...

an Al2 O3 substrate68 and molybdenum oxide on a single crystal.69 The X-rays emitted from a bending magnet of a synchrotron light source is polarized in such a way that the electric vector is parallel to the horizontal plane. Thus the electric dipole moment in this plane in a sample can be easily excited and thus the X-rays are strongly absorbed when a column of atoms is present in this direction. Figure 5.8.1470 shows and orbital components in Cu K XANES spectra of an oxide superconductor single crystal by adjusting a crystal axis to the electric vector of the incident X-rays. This experiment was not a total re ection, but similar to the total re ection method in such a way that both methods used the polarization of X-rays. When L3

Validate (Public Instance Method)

It uses a separate solid body as the cutting tool, so you have to model multi-bodies. The path must start at a point where it intersects the solid cutting tool body (path starts inside or on the surface of the cutting tool). The cutting tool must be definable with a revolved feature. The cutting tool must be made of simple analytical faces (sphere, torus, cylinder, and cone; no splines). You cannot use a guide curve with a solid profile cut (cannot control alignment). The cut can intersect itself, but the path cannot cross itself.

Sun Management Center may be free but it s not a free ride. There is still a good amount of work to do to install and configure the tool. We suggest that you only consider running it on a dedicated console an Ultra 60 or better. The software requires significant disk space and performance to run well. The User s Guide for version 3.0 is nearly 600 pages long, so don t expect to have the tool running in one afternoon. Installation of the basic tool requires the application of appropriate patches afterwards. We found the installation to be a bit cumbersome and modifications to the /etc /system file require a reboot. The Sun Management Center may end up being an important addition to a certain class of sites, especially those with a number of large servers (e.g., SunFires), where the investment is significant and the systems complex enough that any tool helping to manage them is worth its weight in gold. In other environments, its adoption is likely to be slow because of the complexity involved in setting up the software. The basic steps are: 1. Install the software. 2. Create an administrative domain. 3. Populate the domain by creating objects and/or by using the discovery manager. 4. Examine the hierarchical and topological views available through the GUI software. 5. Load and unload modules. 6. Explore modules, processes, logs, and views. 7. View property tables and graphs. 8. Create and test alarms. 9. Creating alarm conditions. 10. Establish security